Undergrounding Pipe Locating System

 

1. Compass display: to display pipe position directly.
2. Left/right arrow indication: use the left/right arrow to indicate the pipe position when route tracing.
3. Right/wrong indication: real-time test the pipe current direction to indicate tracing result and avoid the nearby lines interference.
4. Real-time depth measure and current measure.
5. History curve display: to display the signal variation directly. 
6. Cable Identification: Clamp (optional) identification and sensor identification. Clamp identification can precisely gives accurate result. sensor (optional) identification could be used when the Clamp identification is not applicable.
7. Grounding fault location: Use the A frame (optional) to pinpoint the pipe insulation damaged points against the ground. No need to do zero set and the arrow will point to the fault point direction.
8. Digitization high accuracy sampling and processing,narrow receiving pass band to rise the anti-interference capability and suppress power interference and harmonic interference from nearby running cable and pipe.
9. Multiple locating frequency: active detection and passive detection.
10. Multiple signal output mode: Direct connection output, Clamp Coupling input, Radiation output.
11. Big capacity Li-on batteries series,support auto power off when low battery or long time no operation
12. Solid case and light weight easy to carry .

1. Output Frequency:
2. 640Hz (complex frequency), 1280Hz (complex frequency), 10kHz, 33kHz, 83kHz.
3. Output power: max. 10W, 10 levels adjustable, auto impedance matching.
4. Direct connection voltage: max. 150Vpp.
5. Overload and short circuit protection.
6. HMI: 128X64 LCD.
7. Power supply: 4 X built-in 18650 Li-on batteries, standard 7.4V, 6.8Ah. 

1. Input: Internal receiving loop, Clamp (optional), sensor (optional),fault locating A Frame (optional).
2. Receiving frequency: 

1. Pipe detection mode: wide peak method,narrow peak method,valley method
2. Cable identification mode: Receiving Clamp (optional) intelligent identification and sensor (optional) identification
3. HMI: 320X240 LCD
4. Built-in battery: 2 X 18650 Li-on batteries, standard 7.4V,3.4Ah
5.  Volume: transmitter 270x220x85mm,receiver 700x270x120mm
6.  Weight: transmitter 2.2kgs, receiver 2.2kgs
7.  Charger: input AC 100~240V,50/60Hz,output DC8.4V,2A

   

1. Compass display: to display pipe position directly.
2. Left/right arrow indication: use the left/right arrow to indicate the pipe position when route tracing.
3. Right/wrong indication: real-time test the pipe current direction to indicate tracing result and avoid the nearby lines interference.
4. Real-time depth measure and current measure.
5. History curve display: to display the signal variation directly. 
6. Cable Identification: Clamp (optional) identification and sensor identification. Clamp identification can precisely gives accurate result. sensor (optional) identification could be used when the Clamp identification is not applicable.
7. Grounding fault location: Use the A frame (optional) to pinpoint the pipe insulation damaged points against the ground. No need to do zero set and the arrow will point to the fault point direction.
8. Digitization high accuracy sampling and processing,narrow receiving pass band to rise the anti-interference capability and suppress power interference and harmonic interference from nearby running cable and pipe.
9. Multiple locating frequency: active detection and passive detection.
10. Multiple signal output mode: Direct connection output, Clamp Coupling input, Radiation output.
11. Big capacity Li-on batteries series,support auto power off when low battery or long time no operation
12. Solid case and light weight easy to carry .

1. Output Frequency:
2. 640Hz (complex frequency), 1280Hz (complex frequency), 10kHz, 33kHz, 83kHz.
3. Output power: max. 10W, 10 levels adjustable, auto impedance matching.
4. Direct connection voltage: max. 150Vpp.
5. Overload and short circuit protection.
6. HMI: 128X64 LCD.
7. Power supply: 4 X built-in 18650 Li-on batteries, standard 7.4V, 6.8Ah. 

1. Input: Internal receiving loop, Clamp (optional), sensor (optional),fault locating A Frame (optional).
2. Receiving frequency: 

1. Pipe detection mode: wide peak method,narrow peak method,valley method
2. Cable identification mode: Receiving Clamp (optional) intelligent identification and sensor (optional) identification
3. HMI: 320X240 LCD
4. Built-in battery: 2 X 18650 Li-on batteries, standard 7.4V,3.4Ah
5.  Volume: transmitter 270x220x85mm,receiver 700x270x120mm
6.  Weight: transmitter 2.2kgs, receiver 2.2kgs
7.  Charger: input AC 100~240V,50/60Hz,output DC8.4V,2A

 

Flat Wire Common Mode Inductors

Flat Wire Common Mode Inductors,Vertical Low Profile Common Mode Inductors,Horizontal Flat Wire High Current Inductor,Flat Copper Wire Common Mode Inductors

Shenzhen Sichuangge Magneto-electric Co. , Ltd , https://www.scginductor.com