Luminus Devices has announced that its PhlatLight LEDs are powering two of the newest portable LED-based projectors, the Samsung P400 pocket imager and LG Electronics' HS-102 ultra-mobile projector. Both projectors are lamp-free, weigh less than two pounds and Fit in the palm of a hand.
The PhlatLight PT54 LEDs used in both units enable brightness to reach and exceed 150 lumens, a breakthrough for pocket projectors. The pure RGB color from the PhlatLight LEDs produce a brighter more vivid image than the ANSI brightness specs would suggest, for a picture that's easily Viewable when projected to a 40-inch size even in a well-lit office.
These projectors consume approximately one-third the power of comparable lamp-based projectors and produce an instant-on image at full brightness without the cost and inconvenience of lamp replacement. Both projectors were recently demonstrated at IFA in Berlin and are launching to worldwide distribution. The Samsung P400 is now shipping in the US.
"The HS-102 offers consumers superior picture quality for presentations, games or movies anywhere you want it thanks to the brightness and long-life of PhlatLight LEDs," said Sean Uhm, marketing manager, LG Electronics.
Everlight starts shipping LEDs for micro projectors
Taiwan-based LED packaging company Everlight has received high-power LED orders to be used in micro projectors with shipments starting in September, said a recent report. Although initial order volumes are limited, Everlight is the first to enter the market for micro projectors in Taiwan, according to market sources.
Micro-projectors are a newly developed product and most vendors are using LEDs from US or European LED makers. Everlight is the first Taiwan-based LED maker to provide high-power LEDs to micro projector vendors, the market sources noted.
Everlight indicated that micro projectors require better color saturation, hence RGB LEDs will be used as the light source. Initial monthly shipment estimates are for about 10,000 units, but orders are expected to grow as the market for micro projectors matures in 2009.
Industry players estimated that the market for micro projectors and micro projectors built into handsets may reach 2.34 million units in 2010. However, Taiwan-based Lite-On Technology remains conservative about the new market noting that LEDs typically deliver only one-sixth the brightness of Lite-On said it believes the growth of the micro projector market is limited and it is not considering joining the market at this time.
Optoma has introduced its first micro projector using DLP technology from Texas Instruments (TI), with LEDs as the backlight source. The device is able to project a 20-inch diagonal image from a distance of 50cm. This product is expected to start shipping in October.
3D printing on the pen machine is mainly used in 3 d printing pen, is made from a special custom Dc Gear Motor, mainly used in 3 d printing pen, pen 3 d printing machine has been updated three generations according to the requirements of product.
3D Printing Motor product introduction:
The 3D Printing Motor is based on the deceleration Motor, coupled with supporting gears and ball bearings.The role of the gear reducer is to provide lower speed and greater torque.At the same time, gear box different deceleration ratio can provide different speed and torque.It's mostly rolling.
Features: 3D Printing Motor, small size, large torque, low noise, durable, low energy consumption, customized power design, convenient installation and maintenance;
Simplify design and save space.
Features: usually used financial equipment, office equipment, electronic locks, wireless charger, remote control toys, precision instruments and meters, automobile industry, medical equipment, consumer electronics, household appliances, electric glass doors and Windows, etc., wide application range
Method of use: the best stable in horizontal plane, installed on the 3D Printing Motor output shaft parts, cannot use a hammer to knock, knock prone to press into the 3D Printing Motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
3D Printing Motor should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a 3D Printing Motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
3D Printing Motor should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
The longevity of 3D Printing Motor is greatly affected by the load conditions , the mode of operation,the environment of use ,etc.Therefore,it is necessary to check the conditions under which the product will actually be used .The following conditions will have a negative effect on longevity.Please consult with us should any of them apply.â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
3D Printing Motor
3D Printing Motor,3D Printing Gear Motor,3D Printing Pen Motor,3D Printing Spindle Motor
Shenzhen Shunchang Motor Co., LTD. , http://www.scgearmotor.com