How to install system with u disk

How to install system with u disk

U disk version of the boot disk + ghost system

Special note: The U disk mentioned in this article refers to a USB interface flash disk (commonly known as U disk), not a USB hard disk.
Applicable objects: friends with U disk (friends who are in trouble with CD)
What is the advantage of the PE system over the boot disk of the U disk version, because some PE systems are sometimes chaotic, such as dual systems, when the system drive letter problem, the PE system sometimes cannot be installed normally. If we operate like this, the operation is very clear.

Plug in the U disk, and follow the steps below to make your U disk into a system bootable U disk (note that you should backup useful data in the U disk in advance):

Directly confirm that the USBOOT is running (see the figure below): ①Select your U disk; ② Click the blue word to select the working mode; ③It is strongly recommended to choose the ZIP mode! HDD mode and FDD mode are recommended to try again when the ZIP mode does not work properly; ZIP mode refers to emulating the U disk as a ZIP drive mode, and the letter of the U disk after startup is A: HDD mode refers to emulating the U disk as the hard disk mode ; Special attention: If the HDD mode is selected, the drive letter of the bootable U disk after booting is C :, and it is easy to cause many problems when operating the boot partition, for example: when the system is installed, the installation program will write the boot file to U disk instead of the boot partition of your hard disk! The system installation failed. So please try to choose ZIP mode first. The FDD mode refers to simulating the U disk as a floppy drive mode. After startup, the drive letter of the U disk is A :. The U disk in this mode will not find the U disk when it is started on some machines that support USB-FDD startup, so please be careful use. ④ Click "Start" to start production. ⑤When the warning dialog box appears, make sure that the data in your U disk is useless, and then select "OK". ⑥According to the prompt that appears during the creation of the startup disk, please remove the U disk according to the normal procedure. ⑦According to the prompt that appears during the creation of the startup disk, please insert the U disk according to the normal procedure. ⑧The following successful prompt will appear later, indicating that your USB flash drive has a bootable USB flash drive boot disk. Click × in the upper right corner to close USBOOT. The above is just the first step to complete the U disk system disk. At this time, the disk has the bootable boot disk nature, but it does not carry the system itself, so we should engrave the ghost system (because the ghost system is equipped with PE System, in fact, here is the PE system, not the ghost system itself, but we can enter the PE system to operate the U disk ghost system) Step two: engrave into the ghost system here, I use rain forest trees Wind Ghost XP SP3 installed version YN9.8, it is recommended to use rain forest wind Ghost XP, pretty good, very powerful

Rainforest wood wind Ghost XP SP3 installed version YN9.8 download: http://down.xp222.com/YlmF_XP3_YN9.8.iso

Of course, as long as it is a Ghost installed system, in theory, it will do.

System download: http: //

Here I will use the ghost system as an example to show you: First of all, we should download the engraved software, here I use: UltraISO PE, CD-making tool 9.3 green cracked version http: // After decompression, there are many UltraISO versions online, but in fact The functions are relatively similar. If you have a different version of UltraISO, you can study it yourself. First, insert the U disk into the USB interface of the computer

â‘¡ Run the UltraISO.exe program, select "File"-"Open", select YlmF_XP3_YN9.8.iso file

(That is the package of the rain forest wood wind Ghost XP SP3 installed version YN9.8)

â‘¢ Then select "Boot CD"-"Write Hard Disk Image"

â‘£In the "Hard Drive" item, select the USB drive letter you want to make into a startup disk (if you only have one USB drive,

Usually the default)

⑤ Select USB-HDD + or USB-ZIP + in the "Write Method" item, personally recommend to choose USB-ZIP +, the compatibility is better (it must be noted that when you make the startup disk, what format did you choose, you Now it must be in what format is HDD + in front, and ZIP in front, and ZIP +.)

â‘¥ To choose portable boot-write to the new drive boot sector-(then choose the system, whichever system you want to install, choose the system)

I chose xp here

⑦ Finally, click "Write" and wait a few seconds. After the program prompts that the production is successfully completed, you can pull out the U disk.

In this way, a ghost system of U disk version is completed. The specific installation is the same as the CD installation. Set the first startup item of the computer to USB device startup
In the past, if the system was installed with a CD, the boot item must be adjusted to start with the CD-ROM drive, but now we need to use the U disk to install the system, so we must adjust to the U disk to start. Regarding this, different computers and different versions of bios have different setting methods, but they are all the same. The purpose is to make the first boot item of the computer become a U disk boot. Below we give examples of adjustment methods for several different bios.

The most common Phoenix-Award bios option, just select USB-HDD

dell brand machine bios adjustment options

BIOS of ThinkPad series notebook

BIOS for HP Business Series notebooks

You can see that the above bios options are different, but the adjusted options are for one purpose:

Set the startup item of the computer to start from the USB device, so as to achieve the effect of starting the computer from the U disk.

● Install XP with a bootable U disk

First connect the U disk with the boot function to the computer

Turn on the computer

Emphasis: Because the ghost system is equipped with a PE system, in fact, the boot system is the PE system, not the ghost system itself.
But we can operate the USB flash drive system by entering the PE system. How about it, it seems quite complicated to operate, just follow the steps in detail, it feels simple.